YADE - Revision history

Ezrec: /* Eductor Nozzle */

2007-09-07T12:37:21Z

Eductor Nozzle

← Older revision		Revision as of 12:37, 7 September 2007
Line 17:		Line 17:
	== Eductor Nozzle ==		== Eductor Nozzle ==

	PVC glue the 3/4" CPVC to 1" PVC adapter into the 1 1/4" to 1" PVC bushing, as shown. This will be the eduction nozzle.		PVC glue the 3/4" CPVC to PVC adapter into the 1 1/4" to 1" PVC bushing, as shown. This will be the eduction nozzle.

	[[Image:YADE Eduction Nozzle.jpg]]		[[Image:YADE Eduction Nozzle.jpg]]

Ezrec: /* Mixing Barrell = */

2007-08-14T20:45:59Z

Mixing Barrell =

← Older revision		Revision as of 20:45, 14 August 2007
Line 27:		Line 27:
	[[Image:YADE Intake Nozzle.jpg]]		[[Image:YADE Intake Nozzle.jpg]]

	== Mixing Barrell ===		== Mixing Barrell ==

	Press-fit the 1 1/4" Slip Coupling into the 3/4" slip to 1 1/4" slip bushing, as shown. This is the mixing barrel.		Press-fit the 1 1/4" Slip Coupling into the 3/4" slip to 1 1/4" slip bushing, as shown. This is the mixing barrel.

Ezrec: /* Introduction = */

2007-08-14T20:45:36Z

Introduction =

← Older revision		Revision as of 20:45, 14 August 2007
Line 1:		Line 1:
	= Introduction ==		= Introduction =

	This is Yet Another DIY Eductor - aka YADE.		This is Yet Another DIY Eductor - aka YADE.

Ezrec: /* Introduction = */

2007-08-14T20:45:23Z

Introduction =

← Older revision		Revision as of 20:45, 14 August 2007
Line 1:		Line 1:
	= Introduction ==		= Introduction ==

	This is Yet Another DIY Eductor - aka YADE. ~~The advantage to this model is that~~ the eductor nozzle widens from 3/4" to 1", helping to spread the outgoing flow.		This is Yet Another DIY Eductor - aka YADE.

			Advantages:

			* the eductor nozzle widens from 3/4" to 1", helping to spread the outgoing flow.
			* ABS free (for people who care about that)

	= Parts List =		= Parts List =

Ezrec: /* Final Assembly */

2007-08-14T20:39:27Z

Final Assembly

← Older revision		Revision as of 20:39, 14 August 2007
Line 42:		Line 42:
	Press-fit all 3 components together.		Press-fit all 3 components together.

			Note that I cut this prototype's slots too high. If you do this, just fill in that area with aquarium silicone.

	[[Image:YADE Final Assembly.jpg]]		[[Image:YADE Final Assembly.jpg]]

Ezrec: /* Parts List */

2007-08-13T20:55:26Z

Parts List

← Older revision		Revision as of 20:55, 13 August 2007
Line 5:		Line 5:
	= Parts List =		= Parts List =

	[[Image:YADE Parts.~~png~~]]		[[Image:YADE Parts.jpg]]

	= Construction =		= Construction =

Ezrec at 20:48, 13 August 2007

2007-08-13T20:48:49Z

New page

= Introduction ==

This is Yet Another DIY Eductor - aka YADE. The advantage to this model is that the eductor nozzle widens from 3/4" to 1", helping to spread the outgoing flow.

= Parts List =

[[Image:YADE Parts.png]]

= Construction =

== Eductor Nozzle ==

PVC glue the 3/4" CPVC to 1" PVC adapter into the 1 1/4" to 1" PVC bushing, as shown. This will be the eduction nozzle.

[[Image:YADE Eduction Nozzle.jpg]]

== Intake Nozzle ==

Screw in the 3/4" Barb to 3/4" MIP nylon adapter into the 1" Slip to 3/4" MIP PVC adapter. This will be the inductor nozzle.

[[Image:YADE Intake Nozzle.jpg]]

== Mixing Barrell ===

Press-fit the 1 1/4" Slip Coupling into the 3/4" slip to 1 1/4" slip bushing, as shown. This is the mixing barrel.

[[Image:YADE Mixing Barrel.jpg]]

== Intake Slots ==

Set the intake nozzle, the eductor nozzle, and the mixing barrel next to each other as show. The purple Q-Tip in the picture shows the maximum height of the intake slots.

[[Image:YADE Intake Slot Setup.jpg]]

Cut the slots as show. A radial arm saw is ideal, but a hacksaw will work in a pinch.

[[Image:YADE Intake Slots.jpg]]

== Final Assembly ==

Press-fit all 3 components together.

[[Image:YADE Final Assembly.jpg]]

[[Category:Reef Aquaria]]